This is a press fit mount. Utilization of a sight pusher tool may be required.

This mount fits (including but not limited to):

• Sig Sauer 1911 Stainless Super Target*
• Sig Sauer 1911 Match Elite*
• Sig Sauer 1911 Target Full Size*
• Sig Sauer 1911 Max Full Size*
• STI with adjustable rear sights
• STI Trojan
• STI DVC 3 Gun
• STI DVC Limited
• STI DVC Classic
• Springfield Range Officer
• Springfield Range Officer Elite Target
• Springfield Loaded Target
• Para Elite LS Hunter (with above mentioned modification)
• Remington R1 10mm Hunter (with above mentioned modification)
• Rock Island TCM Rock Target FS HC Combo 22TCM / 9MM
• Rock Island Pro Match ULtra 5” - 45 ACP
• Rock Island Pro Match Tac Ultra 6” - 45 ACP
• Rock Island Pro Match Ultra HC - 40S&W
• Rock Island Pro Match Ultra 6” - 10MM
• Rock Island Pro Match ULtra 6” HC - 10MM
• Iver Johnson Eagle XL-SS10
• Iver Johnson Eagle SS-10
• Iver Johnson Eagle O.D. Green
• Iver Johnson Eagle Coyote Tan
• Iver Johnson Eagle XL-10 Ported
• Iver Johnson Eagle XL-10
• Iver Johnson Eagle XL-45 Ported
• Iver Johnson Eagle XL-45acp
• Iver Johnson Eagle LR

*We have found that some Sig Sauer 1911's with adjustable rear sights use a Kimber Adjustable style rear sight cut. Please measure the distance from the top of the front of the dovetail to the face of the sight cut in your slide. If this measures .43" you will need this (LPA) mount. If it measures .415" you will need the Kimber Adjustable.*

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.604"
Overall Width: .99"
Dovetail Width: .375"
Mounting Hardware: (2) 6-32 Button Head Screws, (1) 6-32 X 3/16 Set Screw

Red Dot Fitment:
Bushnell RXS-100
Crimson Trace CTS-1500
Holosun 407K*
Holosun 407k-GR
Holosun 507K*
Holosun 507k-GR
Holosun EPS-GR*
Holosun EPS-RD*
Holosun EPS-Carry-GR*
Holosun EPS-Carry-RD*
Jpoint
Leupold Delta Point Pro
Optima
Redfield Accelerator
Shield RMS
Shield RMSc
Shield SMS
Sig Romeo Zero

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Minor modification may be neccessary for Rock Islands. Our products should be installed and checked by a qualified and competent gunsmith.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.