This is a press fit mount. Utilization of a sight pusher tool may be required.

This EGW Vortex Venom 1911 mount fits (including but not limited to):

• Sig Sauer 1911 Stainless Super Target*
• Sig Sauer 1911 Match Elite*
• Sig Sauer 1911 Target Full Size*
• Sig Sauer 1911 Max Full Size*
• STI with adjustable rear sights
• STI Trojan
• STI DVC 3 Gun
• STI DVC Limited
• STI DVC Classic
• Springfield Range Officer
• Springfield Range Officer Elite Target
• Springfield Loaded Target
• Rock Island TCM Rock Target FS HC Combo 22TCM / 9MM
• Rock Island Pro Match ULtra 5” - 45 ACP
• Rock Island Pro Match Tac Ultra 6” - 45 ACP
• Rock Island Pro Match Ultra HC - 40S&W
• Rock Island Pro Match Ultra 6” - 10MM
• Rock Island Pro Match ULtra 6” HC - 10MM
• Iver Johnson Eagle XL-SS10
• Iver Johnson Eagle SS-10
• Iver Johnson Eagle O.D. Green
• Iver Johnson Eagle Coyote Tan
• Iver Johnson Eagle XL-10 Ported
• Iver Johnson Eagle XL-10
• Iver Johnson Eagle XL-45 Ported
• Iver Johnson Eagle XL-45acp
• Iver Johnson Eagle LR

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws
(2) 6-32 Flat Head Screws
(1) 6-32 Set Screw

Red Dot Fitment:

• Viridian RFX25
• Vortex Viper
• Vortex Venom
• Burris FastFire
• Burris FastFire 2
• Burris FastFire 3
• Burris FastFire 4
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Cuda RX-795

Our red dot sights are meant to be installed from the left to the right (with the muzzle facing forward). The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included. Minor modification may be neccessary for Rock Islands. Our products should be installed and checked by a qualified and competent gunsmith.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.