HAVE AN AIMPOINT ACRO? USE THIS PLATE TO ADAPT THE DOCTER FOOTPRINT TO THE AIMPOINT ACRO FOOTPRINT
H&K VP9 / P30 / HK45 Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire & Docter
Quick Check: Rear sight replacement optic mount for non-optics-ready H&K pistols.
Fits: H&K VP9, VP9SK, VP40, P30, P30L, P30SK, HK45, HK45C
Footprint: Docter / Vortex / Burris FastFire
Material: 7075 Aluminum
Important: Does NOT fit optics-ready H&K pistols or HK USP models.
This mount is not intended for use with the optics-ready version of these pistols. The optics-ready version can be found here.
The EGW red dot sight mount adapter plate for H&K VP9, VP9SK, VP40, P30, P30L, P30SK, HK45, and HK45C pistols is designed to replace the factory rear sight and provide a low-profile mounting solution for optics using the Docter / Vortex / Burris FastFire footprint.
Our red dot mounts are designed to install from left to right with the muzzle facing forward. The dovetail has a progressive taper to allow for easier installation and proper fitment.
Due to manufacturing tolerances between firearms, minor fitting may be required.
Learn more about optic footprints: RMR vs Docter vs RMSc Footprints Guide
Technical Specifications
- Material: 7075 Aluminum
- Coating: Matte Black Hardcoat
- Overall Length: 1.811"
- Overall Width: .99"
- Torque Specs: 15 in/lbs
- Made in USA
This Mount Fits:
- H&K VP9
- H&K VP9SK
- H&K VP40
- H&K P30
- H&K P30L
- H&K P30SK
- H&K 45
- H&K 45C
This Mount Does NOT Fit:
- HK USP
- Any Optics Ready H&K pistol
This mount is not intended for use with the optics-ready version of these pistols. The optics-ready version can be found here.
Mounting Hardware Included
- (2) 6-32 x 3/8 Flat Head Screws
- (2) 6-32 x 5/16 Button Head Screws
- (1) 6-32 x 3/16 Cup Point Set Screw
Compatible Red Dots
- Viridian RFX25
- Vortex Viper
- Vortex Venom (Open Emitter)
- Burris FastFire
- Burris FastFire 2
- Burris FastFire 3
- Burris FastFire 4
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
- Cuda RX-795
Installation Instructions
- Remove the factory rear sight
- Install the EGW Sight Mount in the dovetail
- Tighten set screw if applicable
- Place the red dot sight on the EGW mount
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15 in/lbs
Why Choose This H&K Red Dot Mount?
- ✔ No permanent slide modification required
- ✔ Low-profile rear sight replacement design
- ✔ Designed for non-optics-ready H&K pistols
- ✔ Precision machined from 7075 aluminum
- ✔ Compatible with popular Docter footprint optics
- ✔ Made in the USA by EGW
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Click here to see a video from Vortex on how to install our red dot base on a slide.
Warning: This product may contain trace amounts of lead. For more information, visit www.P65Warnings.ca.gov.
