Mounting Hardware is Included

This is a press fit mount. Utilization of a sight pusher tool may be required.

WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.

This EGW Mount for Glock - for the Vortex Venom will fit all generation listed below:

• Glock 17
• Glock 17L
• Glock 19
• Glock 19x
• Glock 20
• Glock 21
• Glock 22
• Glock 23
• Glock 24
• Glock 26
• Glock 27
• Glock 29
• Glock 30
• Glock 30 SF
• Glock 31
• Glock 32
• Glock 33
• Glock 34
• Glock 35
• Glock 36 (Our mount is wider than the slide, but it will still work)
• Glock 37
• Glock 38
• Glock 39
• Glock 41
• Glock 42 (Our mount is wider than the slide, but it will still work)
• Glock 43 (Our mount is wider than the slide, but it will still work)
• Glock 43x (Our mount is wider than the slide, but it will still work)
• Glock 44
• Glock 45
• Glock 46
• Glock 48 (Our mount is wider than the slide, but it will still work)
• Canik TP9 SF
• Canik TP9 SA
• Bersa BP9CC
• Tactical Solutions .22lr Conversion
• Taurus G3c
• Taurus GX4 (non optic ready slide)
• Advantage Arms .22lr Conversion
• PSA Dagger (NON-optics ready)

Does not fit Glock MOS models.

• Glock 17 Gen 4 MOS
• Glock 19 Gen 4 MOS
• Glock 34 Gen 4 MOS
• Glock 35 Gen 4 MOS
• Glock 40 Gen 4 MOS
• Glock 41 Gen 4 MOS
• Glock 22 Gen 5 MOS
• Glock 23 Gen 5 MOS
• Glock 34 Gen 5 MOS
• Glock 45 MOS
• Glock 43x MOS
• Glock 48 MOS

WILL NOT WORK WITH ANY CANIK THAT HAS A STEPPED REAR  SIGHT CUT

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Mounting Hardware: (2) 6-32 Button Head Screws, (2) 6-32 Flat Head Screws, (1) 6-32 Set Screw

Red Dot Fitment:

• Viridian RFX25
• Vortex Viper
• Vortex Venom
• Burris FastFire
• Burris FastFire 2
• Burris FastFire 3
• Burris FastFire 4
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Cuda RX-795

Are you looking to replace your factory Glock rear sight with a red dot mounting plate? Our red dot adapter plates for Glocks easily let you mount your red dot to your gun with no modifications to the slide! Our Glock red dot sight mounts are meant to be installed from the left to the right. The dovetail has a progressive taper to allow for easier install.

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Vortex Viper/Venom, Burris FastFire, or Docter red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Red Dot Mounting Plate Installation Instructions

- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Click here to see a video from Vortex on how to install our red dot base on a slide.