HAVE AN AIMPOINT ACRO? USE THIS PLATE TO ADAPT THE DOCTER FOOTPRINT TO THE AIMPOINT ACRO FOOTPRINT
S&W M&P Shield EZ Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire & Docter
Quick Check: Rear sight replacement optic mount for Smith & Wesson Shield EZ pistols.
Fits: S&W M&P Shield EZ .380 ACP and 9mm
Footprint: Docter / Vortex / Burris FastFire
Material: 7075 Aluminum
Important: Reuses factory rear sight screw from the slide
The EGW red dot sight mount for the Smith & Wesson M&P Shield EZ installs in place of the factory rear sight and provides a low-profile mounting solution for optics using the Docter / Vortex / Burris FastFire footprint.
This mount allows you to install optics like the Vortex Venom (Open Emitter), Vortex Viper, Burris FastFire, Viridian RFX25, and other compatible micro red dots without permanent slide modification.
The mount is designed to install from left to right with the muzzle facing forward. The dovetail uses a progressive taper to allow for easier installation and a secure fit.
Learn more about optic footprints: RMR vs Docter vs RMSc Footprints Guide
Technical Specifications
- Material: 7075 Aluminum
- Coating: Matte Black Hardcoat
- Overall Length: 1.811"
- Overall Width: .99"
- Torque Specs: 15 in/lbs
- Made in USA
Compatible Pistols
- S&W M&P Shield EZ .380 ACP
- S&W M&P Shield EZ 9mm
Does NOT Fit
- S&W M&P
- S&W M&P 2.0
- S&W M&P 22
Compatible Red Dots
- Viridian RFX25
- Vortex Viper
- Vortex Venom (Open Emitter)
- Burris FastFire 1
- Burris FastFire 2
- Burris FastFire 3
- Burris FastFire 4
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
- Cuda RX-795
Mounting Hardware Included
- (2) 6-32 x 3/8 Flat Head Cap Screws
- (2) 6-32 x 5/16 Button Head Screws
Important: Nothing installs in the center hole. You must reuse the factory screw from the original rear sight to secure the mount to the slide.
Installation Notes
- Remove the factory rear sight
- Install the EGW mount into the dovetail from left to right with the muzzle facing forward
- Reuse the factory rear sight screw to secure the mount
- Place the optic onto the EGW mount
- Apply blue Loctite to the optic mounting screws
- Torque optic mounting screws to 15 in/lbs
Why Choose This Shield EZ Red Dot Mount?
- ✔ No permanent slide modification required
- ✔ Low-profile rear sight replacement design
- ✔ Compatible with popular Docter footprint optics
- ✔ Precision machined from durable 7075 aluminum
- ✔ Lightweight and rugged for everyday carry
- ✔ Proudly made in the USA by EGW
Important Fitment Information
This mount reuses the factory screw from the original rear sight assembly. No additional center screw is included with this mount.
Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.
Click here to see a video from Vortex on how to install our red dot base on a slide.
Warning: This product may contain trace amounts of lead. For more information, visit www.P65Warnings.ca.gov.
