The EGW red dot sight mount adapter plates for the Walther Q5 Match Optics Ready Models are meant to be installed in the factory slide cut. Simply remove the plate cover and replace it with our mount in order to mount your Vortex Viper, Vortex Venom, Burris FastFire, or Docter red dot sight to your Walther Q5 Match Optics Ready. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Mounting Hardware is Included

WE RECOMMEND THIS PLATE BE INSTALLED BY A QUALIFIED AND COMPETENT GUNSMITH.

This mount fits:

• Walther Q4 Steel Frame OR
• Walther Q4 Tac M1
• Walther Q4 Tac M2
• Walther Q5 Match M1
• Walther Q5 Match M2
• Walther Q5 Match Steel Frame Standard
• Walther Q5 Match Steel Frame Potential
• Walther Q5 Match Steel Frame Standard 10RD

This mount does not fit:

• Walther Q5 Match SF Arabesque
• Walther Q5 Match SF Patriot
• Walther Q5 Match SF Black Diamond
• Walther Q5 Match SF Match Black Tie
• Walther PDP

The screws that come with your slide to mount the plate to the slide may be reused. They are M3 x 6. We currently do not have replacement screws for sale for the plate itself. Walther recommends torquing the screws for the plate to 2Nm or 17.7 in/lbs.

The screws to mount the red dot to the plate are provided at no extra cost. We recommend using 15 in/lbs.

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.968"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 Button Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 Flat Head Screws - Requires 5/64 Wrench or Driver

Red Dot Fitment:

• Viridian RFX25
• Vortex Viper
• Vortex Venom
• Burris FastFire
• Burris FastFire 2
• Burris FastFire 3
• Burris FastFire 4
• Docter
• ADE RD3-001
• ADE RD3-002
• ADE RD3-009
• UTG Reflex Micro Dot
• Crimson Trace CTS-1200
• Crimson Trace CTS-1300
• Sightmark Mini Shot
• Cuda RX-795

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

2 Button Head Cap Screws - Provided for Vortex Viper and Venom Sights
2 Flat Head Cap Screws - Provided for Burris FastFire and Docter Sights

The screws that are included with this mount require a 5/64'' allen wrench for installation.

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Click here to see a video from Vortex on how to install our red dot base on a slide.  

Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.