Specifications

This mount fits:

• Beretta 92 FS
• Beretta 92 G
• Beretta 92 FS Fusion
• Beretta 92 Fusion Black
• Beretta 92 Fusion Blu
• Beretta 92 FS Inox
• Beretta 92 A1
• Beretta 92 FS Brigadier
• Beretta 92 FS Brigadier Inox
• Beretta 92 G Elite
• Beretta 92 Compact
• Beretta 92 Compact w/ Rail
• Beretta 92 Compact with Rail Inox
• Beretta 92 Vertec Inox
• Beretta 92G-SD
• Beretta 92X Centurion
• Beretta 92X Compact
• Beretta 92X Compact w/ Rail
• Beretta 92X Full Size
• Beretta 98 A1
• Beretta 98 FS
• Beretta 90 Series Inox
• Beretta M9
• Beretta M9 Exclusive
• Beretta M9A1
• Beretta M9A3
• Beretta M9A3 Black
• Beretta 98 FS Inox
• Beretta m9 22lr
  
  

This mount does not fit (including but not limited to):

• Beretta 92 Optics Ready Models
• Beretta 92x Performance
• Beretta 92 FS Centennial
• Beretta 92 Performance
• Beretta 92 Performance Defensive
• Beretta 92 RDO Compact Y22
• Beretta M9 A4 Centurion Y22
• Taurus 92

Specifications

Material: 7075 Aluminum
Coating: Matte Black Hardcoat
Overall Length: 1.811"
Overall Width: .99"
Torque Specs: 15 in/lbs

Mounting Hardware:
(2) 6-32 x 5/16" Button Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 x 3/8" Flat Head Screws - Requires 5/64 Wrench or Driver
(2) 6-32 x 5/16" Flat Head Screws - To Secure Plate to Insert - Requires 5/64 Wrench or Driver
(1) Dovetail Insert

Red Dot Fitment:
Bushnell RXS-100
Crimson Trace CTS-1500
Holosun 407K*
Holosun 407k-GR
Holosun 507K*
Holosun 507k-GR
Holosun EPS-GR*
Holosun EPS-RD*
Holosun EPS-Carry-GR*
Holosun EPS-Carry-RD*
Jpoint
Leupold Delta Point Pro
Optima
Redfield Accelerator
Shield RMS
Shield RMSc
Shield SMS
Sig Romeo Zero

Simply remove the rear sight on your gun and replace it with our mount in order to mount your Leupold DeltaPoint Pro, JPoint, Redfield Accelerator, or Optima red-dot sight. You can take our mount off and replace your rear sight at any time. Mounting hardware included.

Installation Instructions
- Remove the rear sight*
- Install the EGW Sight Mount in the dovetail
- Tighten set screw (if applicable)
- Place the red dot sight on the EGW Sight Mount
(placing a small piece of paper between the red dot sight and the sight mount will make for easier removal and will keep Loctite off of the red dot sight.)
- Apply blue Loctite to the provided mounting screws
- Torque mounting screws to 15in/lbs

Modification of your firearm may nullify the manufacturer's warranty.
This product should be installed and checked by a qualified gunsmith.
No liability is expressed or implied for damage or injury which may result from improper installation or use of this product.

Warning: This product may be alloyed with trace amounts of lead and other elements which are known to the State of California to cause reproductive harm and cancer. To prevent exposure, do not alter the product by welding, grinding, etc. For more information, go to www.P65Warnings.ca.gov.