HAVE AN AIMPOINT ACRO? USE THIS PLATE TO ADAPT THE DOCTER FOOTPRINT TO THE AIMPOINT ACRO FOOTPRINT
Taurus G2 / G3 / TX22 Red Dot Mount | Fits Vortex Venom, Viper, Burris FastFire & Docter
Quick Check: Rear sight replacement optic mount for Taurus pistols.
Fits: Taurus G2S, G2C, G3 old style rear sight, PT111 G2, PT140 G2, PT709, PT740, TX22
Footprint: Docter / Vortex / Burris FastFire
Material: 7075 Aluminum
Important: Does NOT fit TORO cuts or optics-ready models
The EGW red dot sight mount for Taurus G2S, G2C, G3, PT111 G2, PT140 G2, PT709, PT740, and TX22 pistols installs in place of the factory rear sight and provides a low-profile mounting platform for optics using the Docter / Vortex / Burris FastFire footprint.
This mount allows you to install optics like the Vortex Venom (Open Emitter), Vortex Viper, Burris FastFire, Viridian RFX25, and other compatible red dots without permanent slide modification.
The mount is designed to be installed from left to right with the muzzle facing forward. The dovetail has a progressive taper to allow for easier installation.
Learn more about optic footprints: RMR vs Docter vs RMSc Footprints Guide
Technical Specifications
- Material: 7075 Aluminum
- Coating: Matte Black Hardcoat
- Overall Length: 1.811"
- Overall Width: .99"
- Torque Specs: 15 in/lbs
- Made in USA
Compatible Pistols
- Taurus G2S
- Taurus G2C
- Taurus G3, old style rear sight, not new Glock-style
- Taurus PT111 G2
- Taurus PT140 G2
- Taurus PT709
- Taurus PT740
- Taurus TX22
Does NOT Fit
- Taurus TORO cuts
- Any factory optics-ready Taurus pistol
- Taurus G3 models with newer Glock-style rear sight cut
Compatible Red Dots
- Viridian RFX25
- Vortex Viper
- Vortex Venom (Open Emitter)
- Burris FastFire 1
- Burris FastFire 2
- Burris FastFire 3
- Burris FastFire 4
- Docter
- ADE RD3-001
- ADE RD3-002
- ADE RD3-009
- UTG Reflex Micro Dot
- Crimson Trace CTS-1200
- Crimson Trace CTS-1300
- Sightmark Mini Shot
- Cuda RX-795
Mounting Hardware Included
- (2) 6-32 x 5/16" Button Head Screws
- (1) 2.6mm x .45mm Flat Head Torx Screw
- (2) 6-32 x 3/8" Flat Head Cap Screws
Installation Notes
- Remove the factory rear sight
- Install the EGW mount into the dovetail from left to right with the muzzle facing forward
- Tighten set screw if applicable
- Place the optic onto the EGW mount
- Apply blue Loctite to the optic mounting screws
- Torque optic mounting screws to 15 in/lbs
Why Choose This Taurus Red Dot Mount?
- ✔ No permanent slide modification required
- ✔ Low-profile rear sight replacement design
- ✔ Compatible with popular Docter footprint optics
- ✔ Precision machined from durable 7075 aluminum
- ✔ Lightweight and rugged for everyday use
- ✔ Proudly made in the USA by EGW
*Red dot not included*
Important Fitment Information
This mount fits the listed Taurus models only and does not fit TORO cuts, optics-ready Taurus pistols, or G3 models with the newer Glock-style rear sight cut.
Warning: This product may contain trace amounts of lead. For more information, visit www.P65Warnings.ca.gov.
